形象气质联用仪—网上增长器定期检查和的操作
2011-05-07
In order to minimize contamination, standard high-vacuum techniques are recommended when handling ETP Electron Multipliers. Clean, powder-free gloves or finger cots should be worn to prevent the transfer of skin oils to critical or mounting surfaces of the multiplier. All tools, mountings, and equipment should be thoroughly cleaned prior to coming in contact with the multiplier. 考虑到避免生态破坏，在ETP光电飙升器作业时介绍使用的完全符合准则的高真空泵工艺。要戴上整洁无尘灰的劳保手套或指尖套来放置面部皮肤油垢污渍生态破坏飙升器的重点还是布置从表面。所以(用得上)的产品，零配件和设配在学习到飙升器前都应该彻底解决拆洗。 Care should also be taken to minimize exposure of the multiplier to dust or other airborne contamination. 运维(进行)时要注意力刻意(制定)减轻将增长器展现在脏污和别空气的危害(的环保中的一次机会)。 Dust particles within the detector may result in increased background noise during operation. 在操作过后测试器内的灰尘颗粒会从而导致(测试的)背景图嗓声加大 Exposure of the multiplier to high humidity should be avoided in order to minimize outgassing during initial operation. If the multiplier exhibits excessive noise due to adsorbed moisture, this condition may be rectified by either leaving the multiplier in high vacuum for about 24 hours, or by using a simple vacuum bake procedure. 要使初始化方法的脱气(日期)实现最大，必须最好特别注意将翻番器表露于高的温度度(的室内环境中)。若是 仍然离心分离了寒湿而使翻番器发生轰鸣声过大(的状况)，都要将翻番器高机械泵度(生活条件)下约24小时内，就是用这个比较简单的机械泵度烘烤步骤。 NOTE: Most models may be backed in vacuum at up to 350℃. Some models may not be baked above 100℃. For information concerning temperature limitations, refer to the installation notes supplied with each ETP Electron Multipliers. 注意力：很多数(元器件)方案需要在高压气下(烘烤)到350℃。许多(元器件)方案无法烘烤不超100℃。光于温湿度要求的相关联消息请参考价值每种个ETP手机培增器的连接表示。 If baking must be done in atmosphere, the temperature must be limited to 120℃ (or lower than 100℃ for some models – see Note above). The multiplier should be heated and cooled slowly to avoid damage due to thermal shock. 倘若烘烤要在没问题臭氧层压下，的摄氏度务必受限在120℃左右(或一系所需要的零部件方案要不超100℃-想泡面的主意应当)。增涨器大概迟滞地调温和闭式冷却塔以尽量避免可能热波动(的摄氏度骤增)而受损。 The rugged design of ETP Electron Multipliers reduces the risk of damage during handling, however, an electron multiplier is a precision component, and all reasonable care should be used when installing or removing. ETP光电飙升器高低一高一低一高一低的(表层)设汁削减了(手)工作期间内伤害的安全风险，不管如此，光电飙升器是个高精度的核心部件，当使用和撤除时都该尽有机会地注意。
